Homework 1
1) 125mm is
-
2) The saw shown •in the illustration is a
-
3)The lathe part shown opposite is called the
-
4)The lathe tool illustrated would be used for
-
5) Identify the drill shown to the right in the illustration.
a) Centre drill b) Plain shank twist drill c) Taper shank twist drill (d) Masonry drill
-
6) Which of the following tools is shown to the right in the illustration?
a) Club hammer (b) Ball pein hammer c) Claw hammer d) Warrington hammer
-
(a) Pair of pincers
-
a) Shooting board (b ) Sawing board © Bench stop (d) Mitre block
________________________________________________________________________________
9) A bevel-
(a) the sides of the blade are bevelled
(c) it is held at a bevel when in use
(d) the cutting edge is bevelled.
_________________________________________________________________________________________
. 10) Odd-
(b) measure the diameter of a hole
(c) mark a line parallel to an edge
(d) check the thickness of a piece of metal
_________________________________________________________________________________________
11) Which of the following would be used to make a hole to start a
small screw?
(a) Centre punch
(b) Bradawl
(c) Nail
_____Homework 2
________________________________________________________________________________________
1) Which tap is used first?
(a) Plug
(b) Taper
_________________________________________________________________________________________
2) The split circular dies shown in the diagram are used for
(a) cutting an internal screwthread in a hole
(b) drilling a flat-
(c) cutting a screwthread on the outside of a round bar
[d) drilling a series
of holes of the same size.
__________________________________________________________
3) Which of the following bits is shown in the illustration?
(a) Auger
(c) Forstner
d) Countersink
_____________________________________________________________________________________________
4) Which of the following is the correct method or using a bradawl
(a) Press the blade into the wood with the edge along the grain
(c) Press the blade into the wood with the edge across the grain
(d) Use as a pilot drill before using the bradawl
____________________________________________________________________________________________________
5) Identify the type of chisel shown in the illustration.
(a) Bevel-
(c) Mortise
(d) Paring
_________________________________________________________________________________________________________________
6) Which material is NOT suitable for making rivets?
(a) Copper
(d) Cast iron
____________________________________________________________________________________________________
7) Which plastic is commonly used to make small gear wheels?
(b) Polythene
_____________________________________________________________________________________________________
8) Which of the following adhesives is waterproof?
(a) P.V.A.
(d) Synthetic resin
_____________________________________________________________________________________________
9) Identify the tool •illustrated opposite.
(a) Narrow chisel
d) Bradawl
___________________________________________________________________________________________
10) Which of the following tools is illustrated opposite?
(a) Try square
(b) Sliding bevel
(c) Mitre square
Homework 3_______________________________________________________________________________
1) The terms "frog" and "cap iron" are associated with which of the
following tools?
(a) Sash cramps
(b) Planes
(c) Hammers
_________________________________________________________________________________________
2) This holding device is called a
(b) G cramp
(c) sash cramp
__________________________________________________________________________________________
3) Which chisel is shown
(a) Firmer
_________________________________________________________________________________________
4) From which material is the mallet head made?
(a) Hide
(b) Copper
________________________________________________________________________________________________________
5) The tool shown in the diagram is a
(a) pillar drill (b) hand drill (c) brace (d) twist drill.
_______________________________________________________________________________________________
6) Which saw should be used cut a curved shape on plywood
(a) Tenon saw (b) Panel saw c) Rip saw (d) Coping saw
_________________________________________________________________________________________________
7) A split circular die is split to
(a) allow swarf to be easily removed
(b) allow for expansion due to temp. variations in the workshop
(c) provide minor adjustment to thread being cut
(d) allow more than one "M" size to be formed.
_______________________________________________________________________________________________
8) A firmer chisel has
(a) a harder blade than other types of chisel
(b) a metal ferrule at both ends of the handle
(c) a blade with rectangular cross section
________________________________________________________________________________________________
" 9) Cross-
(b) mallet
________________________________________________________________________________________________
10) A metal-
(a) cast iron
(d) wrought iron.
_______________________________________________________________________________________________
11) Which of the following is known as the "safe edge"?
(a) The blunt edge of a marking knife
(c) The edge of a hand file which has no teeth
(d) The sloping edge of a chisel
_________________________________________________________________________________
12) A revolving centre is used on a lathe to
(c) support the workpiece at the tailstock end
6. The assessment of a design after its manufacture is called the _____________
